Home › Store Products › Machines & Equipment › Steel & Rebar Equipment
Machines & equipment
Steel & Rebar Equipment
Cutting and bending reinforcement on site and in the yard.
Overview
What this covers
Selected by
Maximum bar diameter and volume.
Type
Bench or portable.
Power
Usually electric; phase matters.
Equipment
Machines in this group
Marked by how we normally hold them. Availability is confirmed at quotation.
Rebar cutting machines
Cutting reinforcement to schedule.
Rebar bending machines
Forming stirrups, hooks and bends.
Combined cut and bend
One machine for both operations.
Portable rebar cutters
Taken to the work.
Portable rebar benders
Bending in position.
Cut-off saws
General steel cutting.
Heavy rebar equipment
Larger diameters and continuous output.
Applications
Typical work
- Cutting reinforcement to a bar bending schedule
- Forming stirrups, links and hooks
- Site cutting where bar arrives in standard lengths
- Yard preparation for multiple pours
- Fabrication shop reinforcement work
Who buys these
Trades and teams
Power
Power and drive options
Most bench machines are electric and many larger ones are three phase. Portable hydraulic units may be electric or manually operated. Confirm the site supply before selecting — a three-phase bender in a yard with single-phase supply is unusable without a generator sized for it.
Comparison
How the options compare
| Bench machine | Portable unit | |
|---|---|---|
| Location | Fixed in a yard or shop | Carried to the work |
| Bar capacity | Generally larger | Generally smaller |
| Throughput | Higher | Lower |
| Setup | Needs a stable base and supply | Minimal |
| Best for | Volume work to a schedule | Site adjustments and smaller runs |
| Availability | Supplier-confirmed availability | Supplier-confirmed availability |
Choosing
How to choose
- State the maximum bar diameter. This is the single figure that determines the machine. A machine rated below your largest bar is unusable for that bar.
- Consider the grade. Higher-grade bar is harder to cut and bend. Capacity ratings assume a grade — check which.
- Bench or portable. Volume work to a schedule points to bench. Site adjustment work points to portable.
- Confirm the supply. Single or three phase, and whether a generator is involved.
- Think about throughput. A machine that cuts slowly is a bottleneck when a pour is waiting.
Accessories
What goes with it
Accessories
Consumables and wear parts
Safety equipment
Ownership
Maintenance, spares and service
Cutting dies and bending formers are wear parts. Keeping them sharp and correctly set matters more to output than machine power does. Hydraulic units need oil level and seal checks.
Record the model and serial number. Dies and formers are model-specific, and matching a replacement years later depends on knowing which machine it is.
Price
What affects the price
- Maximum bar capacity
- Bench or portable
- Motor rating and phase
- Cutting speed
- Brand
- Dies and formers included
- Warranty and service terms
- Spare parts availability
- Quantity
Availability
What affects availability and lead time
- Common bench cutters and benders available through the supplier network in limited quantity
- Heavy-capacity machines and combination units sourced on order
- Three-phase models generally need supplier confirmation
- Larger machines need transport and offloading planning
Quotation
What to send with an enquiry
- Maximum bar diameter you need to process
- Bar grade
- Approximate volume per day or per pour
- Bench or portable preference
- Power available and whether single or three phase
- Whether cutting, bending or both
- Quantity and preferred brand
- Existing machine model if replacing
Avoid
Common mistakes
- Choosing capacity from the usual bar rather than the largest bar
- Ignoring bar grade when reading a capacity rating
- Ordering three phase without confirming the supply
- Not budgeting for dies and formers
Questions
Frequently asked
What details are needed to buy a rebar bending machine?
Maximum bar diameter, bar grade, and expected volume. Those three narrow it immediately.
Then power available and whether it is single or three phase, and whether the machine stays in one place or moves. Send those and we will identify suitable options against manufacturer specifications.
Can one machine cut and bend?
Combination machines exist and suit smaller operations where space and budget are constrained. Separate machines generally give higher throughput because one operation does not wait for the other.
Where to go next